Tomy FLS-1000 Operator'S Manual Download Page 6

Page: 6 / 64

ー 5 ー

WARNING

Make sure that holes inside the chamber

are not blocked by articles to be sterilized.

If the vent hole is blocked by such items

as sterilization bags, the chamber pressure

cannot be controlled, thereby causing

serious accident such as explosion of the

chamber. Make sure that articles to be

sterilized are placed in a container, such

as a basket provided with the FLS-1000 to

prevent the vent hole and its surrounding

area from being blocked.

Stop operation immediately when the

pressure gauge pointer is over the red

line.

Otherwise, parts can be damaged and

broken parts may scatter, resulting in burns,

injury or serious accident. In this case, stop

operation immediately and contact your

dealer or our local representative.

Use special caution when handling the

articles to be sterilized that may be very

hot after the operation.

Handling hot articles can cause burns.

Use special caution when handling the

hot liquid that may suddenly boil over.

The sterilized liquid inside the chamber is

cooled down slowly than the chamber and

may boil over suddenly on any shocks. This

bumping may cause burns or unexpected

accident.

Do not leave any contamination inside

the chamber or in the sterilizing water.

Failure to do so may cause corrosion or

damage on the chamber. It may also cause

malfunction of the water level sensor,

which may hamper the empty heating

prevention function, resulting in fire.

Be sure to unplug the FLS-1000 before

performing maintenance procedures.

Failure to do so may cause electric shock.

For models with no power plug provided,

the power circuit breaker to which the

power plug is connected should be turned

off.

Do not operate the FLS-1000 if any

corrosion, damage, deformation or loose

connections are found on its chamber,

chamber lid, hinges, hinge shafts,

retaining rings, lid hooks, or lid hook

catches.

Otherwise, explosion may occur while the

pressure rises, resulting in death, injury

or serious accident. If any abnormality is

found, please contact your dealer or our

local representative.

Do not operate the FLS-1000 if any crack,

deformation or damage is found on its

chamber lid gasket.

Otherwise, steam leak may occur, resulting

in burns. If any abnormality is found,

please contact your dealer or our local

representative.

After replacing the chamber lid gasket,

be sure to make a test run.

If the chamber lid gasket is not installed

properly, steam may leak and cause burns.

Unplug and inspect the power plug

regularly.

Failure to do so may cause fire or burnout.

Do not operate the FLS-1000 if the

chamber lid handle is deformed or

damaged.

Failure to do so may cause burns or injury.

If any abnormality is found, please contact

your dealer or our local representative.

Do not attempt to open the drain cock

unless the pressure gauge reads 0MPa.

If the drain cock is opened when pressure

still remains in the chamber, hot water may

spurt out, causing death, injury or serious

accident.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands