Tomy FLS-1000 Operator'S Manual Download

Page: 14 / 64

ー 13 ー

①

②

③

④

⑤

⑥

⑦

⑧

Access port

The temperature sensor for articles to be sterilized or the external temperature sensor can be

installed into the chamber through this port.

Temperature sensor

It detects the temperature inside the chamber.

Heating element (heater)

It heats the sterilizing water.

Vent hole

Air is discharged from the chamber through this hole. The hole leads to the exhaust tank, the

trap bottle, and the steam exhaust vent.

Water level sensor

It detects the level of sterilizing water in the bottom of the chamber.

Drain hole

Sterilizing water in the chamber is drained through this hole. The hole leads to the drain port.

Chamber bottom plate

It is provided to prevent articles to be sterilized from contacting with a heater at the bottom of

the chamber.

Water level indicator

It is provided to check the water level in the chamber.

Chamber Interior

①

⑥

②

⑤

④

⑧

⑦

③

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands