Tomy FLS-1000 Operator'S Manual Download

Page: 20 / 64

ー 19 ー

To move the FLS-1000 hold the top of the unit on both sides of the chamber lid handle with

both hands and carefully push it.

※

Four casters are mounted in the four corners of the bottom of the FLS-1000. A caster in the corner

where the chamber lid handle is attached on top is a fixed one, and casters on each of the other

three corners are swivel ones.

※

Never attempt to lift the FLS-1000 while it is being moved. This model is not designed to be lifted

up.

①

To move and install the FLS-1000

To install the FLS-1000 select a location in a room that is well ventilated and free of direct

sunlight.

Place the FLS-1000 onto a solid flat surface such as a concrete floor.

※

Weight of the FLS-1000 : 108kg

Avoid installing the FLS-1000 in a slippery place or a place which may be exposed to

vibration.

Considering the steam coming from steam exhaust vent and surrounding area, install

FLS-1000 providing a clearance of at least 25cm at the rear and on each side of the unit.

When operating the FLS-1000, the following environmental requirements should be met:

○

Installation Location

: 10 to 35°C

: 750 to 1060hPa

: less or equal to 75

％

: below 2,000m

: 2 degrees

: Class II

: 2

Ambient temperature range

Atmospheric pressure range

Relative humidity

Altitude

Maximum gradient

Overvoltage category

Pollution degree

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands