Tomy FLS-1000 Operator'S Manual Download Page 31

Page: 31 / 64

ー 30 ー

5-5. Checking the Sterilizing Water in Chamber

Open the chamber lid and check that the sterilizing

water in the chamber is not contaminated. Drain

water from the chamber if the sterilizing water is

contaminated.

※

For drainage of water, please refer to “5-11. Draining

the Sterilizing Water from the Chamber”.

Check that the water level in the chamber is suffi cient

enough to cover the water level indicator. Add water

to the chamber, if necessary, until the indicator is

completely covered with water.

※

The water level in the chamber should be maintained

only barely higher than the surface of the water level

indicator to prevent articles to be sterilized from

getting wet.

※

To sterilize the large amount of liquid in a bucket, fi ll

the chamber with water until the bottom of the bucket

is covered to approximately 5 cm.

Check the low sterilizing water level indicator turns

off .

To check the quality and amount of sterilizing water

①

②

③

The FLS-1000 generates steam by heating up the sterilizing water in the chamber, which has

a heating element in its bottom. Check the quality and level of the sterilizing water inside the

chamber to perform adequate sterilization.

Use tap water as sterilizing water. When purifi ed water or cold water is used, the water level

sensor may not correctly detect the level of the sterilizing water in the chamber.

If tap water has inferior quality, purifi ed water may be added to fi ll the chamber. In such a

case, fi ll the chamber with purifi ed water fi rst until the water level indicator is covered in

water and then, fi ll it with tap water until the low sterilizing water level indicator turns off .

Quality of tap water may vary widely, depending on location. Therefore, it is recommended that

approximately 300mL of tap water per 3L of purifi ed water be used as a guide.

•Up to 5cm above the bottom of the bucket

approx. 6.7L

•Up to the chamber bottom plate

approx. 6.0L

•Up to the water level indicator

approx. 4.4L

Approximate indication of the amount of water in the chamber

５㎝

Bucket

Water Level Indicator

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Tomy FLS-1000, Operator'S Manual, Page: 31 / 64

Search results

Summary of Contents for FLS-1000

Reviews: