Tomy FLS-1000 Operator'S Manual Download

Page: 59 / 64

ー 58 ー

Error code

Possible cause

Remedy

A01

The start key is pressed before draining and

pouring water into the chamber.

※

The default value is 40 cycles.

Refer to “6-10. Sterilizing water change Alert

Function”.

A02

The start key is pressed when the water

level in the chamber is low.

※

Low sterilizing water level is detected.

Fill the chamber with water.

A03

The start key is pressed when the lid open/

close system failed to detect the lid status.

※

Open then close the lid.

A04

The start key is pressed when the lid remains

open.

Close the lid.

A05

The start key is pressed when the drain

access cover remains open.

The drain access cover is opened during the

operation.

Close the drain access cover.

A06

The start key is pressed when the exhaust

tank is full.

Drain the exhaust tank.

A07

The start key is pressed when the

temperature inside the chamber is below

0℃.

Wait until the chamber temperature rises to the

operating temperature.

A09

Power-off is detected after a sterilization

process has started or before it has completed.

Refer to “6-5. Power Failure Alert Function”.

A10

The memory approaches the end of its

lifetime. (E26)

※

An alarm notification appears when

％

, 90

％

, 95

％

, 98

％

, 99

％

, and 99.5

％

of the lifetime is reached.

Press the check key once to clear the error, and

enable the system.

A20

The start key is pressed while printing.

Press the check key once.

A21

Printer trouble.

※

Printer error includes: cover open, paper

out, printer head abnormal temperature,

and disconnection.

Refer to “7. Optional Functions”.

A30

The calendar battery has reached the end of

its lifetime.

Press the check key once to clear the error, and

enable the system.

Contact your dealer or our local representative.

CHECK

Timing of the annual voluntary inspection

approaches.

※

Reminder activates 30 days before the

due date, and on and after the day of the

due date.

Press the check key once to clear the error,

and enable the system. Refer to “6-6. Annual

Inspection Reminder Function”.

Operation Error Code Table

※ 1

The FLS-1000 checks the operation of the lid open/close detection system to ensure its safe operation, therefore, open and

close the lid at least once before each operation or timer operation.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands