Tomy FLS-1000 Operator'S Manual Download Page 52

Page: 52 / 64

ー 51 ー

7. OPTIONAL FUNCTIONS

The following optional accessories and functions are available for the FLS-1000.

Data output function

The data output function allows producing up to 3 outputs of process data in analog form,

including chamber temperature, temperature of articles to be sterilized, chamber pressure.

The data can be stored to an optional recorder when it is connected.

■

Printer

Data of the chamber temperature, chamber pressure and article temperature can be printed

out on the optional printer.

■

Brackets for anti-tip straps

Metal brackets for anti-tip straps are provided to secure the autoclave with a commercially

available overturn prevention strap or wire.

■

The external temperature sensor for articles to be sterilized

Sterilization process is monitored using the temperature sensor for articles to be sterilized

by installing it directly into the article in the chamber so that the autoclave begins the

sterilization time countdown only when the temperature for articles to be sterilized has

reached a set sterilization temperature and, therefore, provides adequate heating.

※

The temperature is controlled to within 0℃ to

＋

2℃ of the set temperature.

※

The lid interlock release and the cycle complete temperatures can also be measured and monitored

by the external temperature sensor for articles to be sterilized.

■

For the operation of the optional accessories and functions, please refer to the supplement to

the Operator’s Manual; “FLS-1000 Autoclave Optional Functions”.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands