Tomy FLS-1000 Operator'S Manual Download

Page: 22 / 64

ー 21 ー

3-2. Connecting to the Power Source and Grounding

WARNING

Connect the FLS-1000 to a power outlet of the

voltage specified as correct for FLS-1000. Do not

connect it to a shared outlet.

●

Failure to do so may cause accidental fire, short circuit

or malfunction.

Do not use extension cords or power strips.

●

Failure to do so may cause accidental fire, short circuit

or malfunction.

Make sure that the FLS-1000 is properly

grounded.

●

Failure to do so may cause explosion, electric shock or

malfunction.

Never ground the FLS-1000 through a water

main or a gas pipe.

●

Failure to do so may cause explosion, electric shock or

malfunction.

To protect against electric shock adequate grounding of FLS-1000 must be provided. When it cannot

be provided, arrange for a qualified electrician to carry out the necessary grounding work.

The FLS-1000 employs a plug with a two-pole grounding electrode. Plug the FLS-1000 into a two-

pole socket outlet of the voltage specified as correct for FLS-1000.

※

For the power requirements of the FLS-1000 please refer to “11-1. Specifications of the FLS-1000”.

Plug the FLS-1000 directly into a power outlet of the specified voltage. Do not connect it to a shared

outlet.

Leave sufficient space around the power outlet so that the plug can be easily unplugged.

※

When hearing thunder, unplug the power plug from the outlet to prevent lightning damage.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands