Tomy FLS-1000 Operator'S Manual Download Page 35 | Manualshive

Page: 35 / 64

background image

ー 34 ー

When sterilizing a large amount of liquid, it will take a longer time to raise the temperature

for articles to be sterilized. Therefore, it is recommended that the operating time should be

extended referring to the following figure:

Extended sterilization time for liquid sterilization (reference example: sterilization for 20

minutes at 121℃)

0.5L of water in a container

(for 20 minutes) + 12 minutes

1L of water in a container

(for 20 minutes) + 17 minutes

2L of water in a container

(for 20 minutes) + 28 minutes

5L of water in a container

(for 20 minutes) + 38 minutes

10L of water in a container

(for 20 minutes) + 67 minutes

<

To perform effective sterilization

>

○

The FLS-1000 controls the temperature using the temperature detected by the temperature

sensor in the chamber as an index. When more reliable sterilization is required, set the

appropriate conditions for sterilization using an external temperature sensor for articles to be

sterilized or a sterilization index body.

○

«
...
33
34
35
36
37
...
»

Summary of Contents for FLS-1000

































































Reviews:

No comments

Related manuals for FLS-1000

Brand: Fein Pages: 248

Brand: ZF Pages: 30

Brand: Raymarine Pages: 111

Brand: Camozzi Pages: 2

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: MADRIX Pages: 12

Brand: Narcotrend Pages: 47

Brand: IDEAL Networks Pages: 10

ActiveFinder One

Brand: LaserLiner Pages: 92

Brand: Mackie Pages: 18

Brand: Mackie Pages: 2

Brand: Mackie Pages: 8

Brand: Mackie Pages: 7

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: Yamaha Pages: 16

Brand: Aveo Engineering Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands