Tomy FLS-1000 Operator'S Manual Download Page 60

Page: 60 / 64

ー 59 ー

9-3. Contact Information

WARNING

When returning FLS-1000 or any parts of FLS-1000 for replacement or

repair, FLS-1000 or the parts must be appropriately decontaminated

before shipping it in any of the following cases:

In cases where FLS-1000 or any parts of FLS-1000 has been exposed to

infectious and hazardous or radioactive substances.

In cases where FLS-1000 or any parts of FLS-1000 has any residue of blood or

other chemicals and has been identified as hazardous.

1 :
2 :

For Assistance or Service Contact ;

TOMY DIGITAL BIOLOGY CO., LTD.

3-14-17 Tagara, Nerima-ku, Tokyo 179-0073, Japan
e-mail : [email protected]
URL : http://www.digital-biology.co.jp
phone : +81-3-5971-8160 fax : +81-3-3970-6036

TOMY SEIKO CO., LTD.

If any system malfunction or abnormality in FLS-1000 is suspected, contact your dealer or the

following TOMY offices.

TOMY KOGYO CO., LTD.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands