Tomy FLS-1000 Operator'S Manual Download Page 5

Page: 5 / 64

ー 4 ー

WARNING

Make sure that the FLS-1000 is properly

grounded.

Failure to do so may cause explosion,

electric shock or malfunction.

Never ground the FLS-1000 through a

water pipe or a gas pipe.

Failure to do so may cause explosion,

electric shock or malfunction.

Do not touch the power switch with a

wet hand.

Failure to do so may cause electric shock.

Never attempt to open the lid until the

chamber pressure returns to 0MPa.

If the lid is opened while pressure remains

in the chamber, articles to be sterilized or

steam may gush out, thereby resulting in

death or serious injury.

Do not bend the exhaust hose.

If exhaust venting is not carried out

smoothly, the chamber pressure may

become abnormally high, thereby causing

damage to parts. Broken parts may scatter

and cause burns, injury or serious accident.

When the pressure gauge is not working

properly, stop operation.

Otherwise, abnormality inside the

chamber, if any, cannot be found, thereby

causing serious accident. If pressure gauge

malfunction is suspected, please contact

your dealer or our local representative.

Be extremely careful of steam coming

out of the chamber when opening the

chamber lid.

Steam coming out of the chamber is very

hot and can cause burns or injury.

Do not use the FLS-1000 to sterilize

sealed articles.

Sealed articles may explode or burst when

they are removed from the chamber,

thereby causing burns, injury or serious

accident. The chamber pressure may

become abnormally high, thereby causing

damage to parts. Broken parts may scatter

and cause burns, injury or serious accident.

Do not sterilize any cracked or damaged

glassware.

Damaged glassware may explode or burst

when it is removed from the chamber,

thereby causing burns, injury or serious

accident.

Do not use the FLS-1000 to sterilize

flammable or explosive articles.

Failure to do so may cause fire or explosion.

Do not use extension cords or power

strips.

Failure to do so may cause accidental fire,

short circuit or malfunction.

Avoid leaving any foreign materials

between the chamber lid gasket and the

chamber.

Failure to do so may cause steam leak,

thereby resulting in burns.

Do not use the FLS-1000 to sterilize

corrosive articles.

Otherwise, the chamber may corrode and

explode or burst while pressure rises,

thereby causing death, injury or serious

accident.

Connect the FLS-1000 to a power outlet

of the voltage specified as correct for

FLS-1000. Do not connect it to a shared

outlet.

Failure to do so may cause accidental fire,

short circuit or malfunction.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands