Tomy FLS-1000 Operator'S Manual Download Page 37

Page: 37 / 64

ー 36 ー

Check that the READY indicator is on. If it is off,

follow the instructions stated in the table on the

next page to turn the READY indicator on.

Press the START key.

The autoclave will start an operation in a few

seconds after performing the checking of the

safety system.

For details on the indicator and buzzer, please

refer to “Operation of the indicator and buzzer in

each process of the sterilization cycle” stated in the

table on the next page.

※

To temporarily suspend operation, press the stop key during the operation.

※

If an error occurs during the operation, the indicator of the current operating process on the work

monitor continues to flash red.

※

If a power failure occurs during the operation, the POWER FAIL indicator lights up.

①

②

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

※

While the lid open, low sterilizing water level, drain, drain access cover open or sterilizing water

change indicator is on, the READY indicator does not turn on.

Cause

Remedy

Lid open indicator is on.

Check the opening/closing of the lid and then close the lid completely again.

Low sterilizing water level indicator is on. Fill the chamber with water.

Drain indicator is on.

Drain the exhaust tank.

Drain access cover open indicator is on.

Close the drain access cover.

Sterilizing water change indicator is on.

Drain and pour water into the chamber.

Table. Cause and remedy when the READY indicator does not turn on

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Brands by name

Popular brands