Tomy FLS-1000 Operator'S Manual Download

Page: 43 / 64

ー 42 ー

Press the TIMER key.

The timer indicator turns on and the time display

shows the currently set value of the waiting time.

Press the time setting up and down arrow keys

to set a value of the waiting time while the timer

indicator is on.

※

Timer setting range

：

〜

：

〜

99 hours

Press the START key while the timer indicator is

on. The autoclave will enter into the timer mode in

a few seconds after performing the checking of the

safety system. The time display shows the waiting

time until the autoclave starts an operation.

※

The operation can be interrupted by pressing the

STOP key.

①

②

③

6-4. Timer Function

The timer function allows the operator to set the waiting time for the operation to start.

To set the timer follow the procedures given below after setting the desired operating

parameters.

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands