Tomy FLS-1000 Operator'S Manual Download

Page: 23 / 64

ー 22 ー

3-3. Setting the Altitude Level

Press the FUNCTION key while the READY

indicator is on. The time display flashes

“F00”.

Press the time setting up and down arrow

keys to show “F20” in the time display.

The temperature display shows the altitude

level code.

Press the START key.

The temperature display starts to flash.

Press the temperature setting up and down

arrow keys to display the altitude level code

that corresponds to the location where the

FLS-1000 is installed.

To set the altitude level

①

②

③

④

The FLS-1000 operates by generating steam under pressure and temperature. Therefore, its

sterilization process can be greatly affected by the atmospheric pressure at the location where

the FLS-1000 is installed. In order to ensure proper operation of the FLS-1000 please reset the

altitude level if it is moved to another location.

Table. Altitude level code and the corresponding altitude level and maximum

setting sterilization and lid interlock releasing temperatures.

Altitude level code

Altitude level

Maximum setting

sterilization temp.

Maximum lid interlock

releasing temp.

Below 800m

123℃

100℃

Above 800m

〜

below 1500m

122℃

97℃

Above 1500m

〜

below 2000m

121℃

95℃

Press and hold down the START key.

The buzzer will sound in approximately 4 seconds to indicate that the setting is finalized and

the display will return to the normal.

⑤

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

COMPLETED

POWER

FAILURE

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands