Tomy FLS-1000 Operator'S Manual Download Page 57

Page: 57 / 64

ー 56 ー

9-2. Error Code Table

Error code

Possible cause

Remedy

E04

Level of sterilizing water becomes

insufficient during the operation.

Turn off the power switch and wait until the

chamber pressure becomes 0MPa to open the lid.

And then pouring water into the chamber.

E05

Temperature inside the chamber is much

higher than the set temperature during the

sterilization process.

※

It exceeds the set value by 5℃ or more.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E06

Pressure inside the chamber rises because

the shape of the article to be sterilized serves

to prevent air from escaping.

※

The pressure exceeds 175kPa.

Turn off the power switch and wait until the

chamber pressure becomes 0MPa to open the

lid. And then take some measures to allow air to

escape from the load or reduce the volume of the

load.

(Refer to “5-6. Placing Articles to be Sterilized”.)

E07

Chamber temperature sensor is disconnected

or broken.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E08

The temperature inside the chamber is much

lower than the set temperature during the

sterilization process.

※

It is more than 5℃ lower than the set

value.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E09

Chamber lid opens during the operation.

※

Lid open is detected by the sensor.

Close the chamber lid securely. If this happens

during the operation, unplug the power plug of

the FLS-1000 from the outlet and contact your

dealer or our local representative.

E10

Interlocking system of the chamber lid is not

activated.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E11

Temperature does not rise during

temperature rising and temperature and

pressure rising processes.

※

Temperature rises less than 2℃ within

the specified time limit. A temperature

equal to or below 60℃ in 120 minutes,

and above 60℃ in 40 minutes.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E12

Pressure sensor is disconnected or broken.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E13

External temperature sensor for articles to

be sterilized is disconnected or broken.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E15

Air vent valve is broken.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

System Error Code Table

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands