manualshive.com logo in svg

Tomy FLS-1000, Operator'S Manual, Page: 4 / 64

Share
Download
Tomy FLS-1000 Operator'S Manual Download Page 4

ー 3 ー

WARNING

Do not modify or alter the FLS-1000 or 

any parts of the FLS-1000.

Failure to do so may cause serious accident 

or malfunction.

When leaving the FLS-1000 out of use for 

a long time, be sure to unplug the power 

plug of the FLS-1000 from the outlet.

Failure to do so may allow insulation 

to deteriorate, thereby causing electric 

shock, short circuit or fire. For models 

with no power plug provided, the power 

circuit breaker to which the power plug is 

connected should be turned off.

Do not use accessories or parts other than 

those specified by the manufacturer.

Failure to do so may cause serious accident 

or malfunction.

Do not install the FLS-1000 in a place 

where chemicals that are likely to 

generate flammable or corrosive gases or 

fumes are stored.

Failure to do so may cause fire. Electric 

components can corrode and cause short 

circuit or electric shock.

Do not allow such foreign objects as 

pieces of metal, combustible materials, 

water or other liquids to enter the 

interior of the FLS-1000 through its vents 

or other openings.

Failure to do so may cause short circuit, fire 

or malfunction.

Do not remove the outer panel of the 

FLS-1000.

Contact with the inner parts of FLS-1000 

may cause electric shock, burns, fire or 

malfunction.

Do not touch the power plug with a wet 

hand.

Failure to do so may cause electric shock. 

Do not use any damaged power cord, 

plug or loose outlet.

Failure to do so may cause accidental fire, 

short circuit or malfunction.

Do not allow the power cord to be 

pinched by or caught between heavy 

objects.

Failure to do so may cause accidental fire, 

short circuit or malfunction.

Avoid installing the FLS-1000 in a place 

where there is a lot of dust or moisture.

Failure to do so may cause short circuit of 

electric components or fire.

Avoid installing the FLS-1000 in or near 

a sink or tap where there is a risk of it 

being splashed with water.

Failure to do so may cause short circuit or 

electric shock.

Install the FLS-1000 on a sturdy and level 

surface such as concrete floors that can 

support its weight.

Failure to do so may cause FLS-1000 to fall 

over, thereby resulting in personal injury or 

physical damage.

Do not unplug by pulling on the cord.

Stress to the cord may cause a loose 

connection in the plug and result in fire or 

burnout of the cord.

 1-2.  Warnings and Cautions

Summary of Contents for FLS-1000

































































Reviews:

No comments