Thermal Dynamics ULTRA-CUT 200 XT, Operating Manual

Page: 96 / 228

ULTRA-CUT 200 XT
4-20 OPERATION Manual 0-5304
CCM Status Code
Group 2 -- Plasma Power Supply
Code Message
Remedy / Comments
262
Inverter 2B Over Temp
Ambient
Inverter circuitry is over temperature likely cause is ambient greater than 40 deg
C; Reduce power supply cutting Duty Cycle; Reduce ambient air temperature; Add
auxiliary cooler.
263
Inverter 3A Over Temp
Ambient
Inverter circuitry is over temperature likely cause is ambient greater than 40 deg
C; Reduce power supply cutting Duty Cycle; Reduce ambient air temperature; Add
auxiliary cooler.
264
Inverter 3B Over Temp
Ambient
Inverter circuitry is over temperature likely cause is ambient greater than 40 deg
C; Reduce power supply cutting Duty Cycle; Reduce ambient air temperature; Add
auxiliary cooler.
265
Inverter 1A No Input
Power
Inverter section may have no input power. Contactor W1 not closed; Defective con-
tactor or CB4 tripped; Inverter section input not connected; Defective Inverter.
266
Inverter 1B No Input
Power
Inverter section may have no input power. Contactor W1 not closed; Defective con-
tactor or CB4 tripped; Inverter section input not connected; Defective Inverter.
267
Inverter 2A No Input
Power
Inverter section may have no input power. Contactor W1 not closed; Defective con-
tactor or CB4 tripped; Inverter section input not connected; Defective Inverter.
268
Inverter 2B No Input
Power
Inverter section may have no input power. Contactor W2 not closed; Defective con-
tactor or CB4 tripped; Inverter section input not connected; Defective Inverter.
269
Inverter 3A No Input
Power
Inverter section may have no input power. Contactor W2 not closed; Defective con-
tactor or CB4 tripped; Inverter section input not connected; Defective Inverter.
270
Inverter 3B No Input
Power
Inverter section may have no input power. Contactor W2 not closed; Defective con-
tactor or CB4 tripped; Inverter section input not connected; Defective Inverter.
271
Inverter ID reading
fault
CCM found ID values inconsistant during reading. CCM to an Inverter section rib-
bon damaged or disconnected; Inproper ribbon cable routing.
CCM Status Code
Group 3 -- Gas Controller Status & Protocol
Code Message Remedy / Comments
301
Gas control communication
fault
Problem with fiber optic cable to GCM 2010 or DMC or DPC; Dirt on fiber ends
or in connectors; blow out with clean dry air. Fiber not locked into connector;
Sharp bends in fiber cable; Fiber defective; GCM 2010 circuit board defect;
DMC or DPC power supply defective; DMC or DPC circuit board defect
302 Gas Control reply fault
Problem with fiber optic cable to GCM 2010 or DMC or DPC; Dirt on fiber ends
or in connectors; blow out with clean dry air. Fiber not locked into connector;
Sharp bends in fiber cable; Fiber defective; GCM 2010 circuit board defect;
DMC or DPC power supply defective; DMC or DPC circuit board defect
303
Gas Supply Pressure out of
range.
GCM 2010 inlet plasma or shield pressure low or defective pressure sensors
PS3 & PS4; Defective GCM 2010 PCB; For DFC 3000 see DPC for pressure
faults.
304 Gas Control Purging
Normal following power up or returning from Plasma Disable. Wait for purge
to finish.
305 Gas Control protocol error
Verify Firmware revision for compatibility with GCM 2010 or DMC and DPC
306 Not used Reserved for other future use.
307
Gas Control sequencing
error Verify Firmware revision for compatibility with GCM 2010 or DMC and DPC
308 Gas Control Type Mismatch Wrong CCM (Auto-Cut or Pak 200 type?) for Ultra-Cut; Install correct CCM