TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 93

Page: 93 / 154

When the 2nd digit of Sn-10 is 1, the output frequency decreases at the rate determined by

the deceleration time. For positioning applications, specify “stall prevention during deceleration

not provided” (2nd digit = 1) in order to obtain stopping accuracy. With large load inertia, use

a braking resistor (For 460V: 5HP~30HP and 230V: 5HP~25HP and 600V: 5~25HP) or braking

transistor with braking resistor to prevent overvoltage.

•

3rd digit

(stall prevention during run)

3rd digit = 0:

Stall prevention during run is enabled.

3rd digit = 1:

Stall prevention during run is not enabled.

Stall prevention operation during run starts decelerating when the output current is greater

than the set value of Cn-30 (operation level of stall prevention during running) for more than

100msec. The AC drive decelerates as long as the output current exceeds the set value of Cn-30.

When the output current goes below the set value, the AC drive reaccelerates. The deceleration

time selected in the 4th digit of Sn-10 is used. Even during stall prevention while running,

stall prevention during deceleration and stall prevention during acceleration are enabled.

•

4th digit

(selection of deceleration time during stall prevention during run)

4th digit = 0:

The AC drive decelerates for the time speciﬁed in bn-02.

4th digit = 1:

The AC drive decelerates for the time speciﬁed in bn-04.

(11) Protective Characteristics Select 2 (Sn-11)

•

1st digit

(Not used)

2nd digit

(fault contact signal during auto reset/restart operation)

2nd digit = 0:

A fault contact signal is not asserted during auto reset/restart operation.

2nd digit = 1:

A fault contact signal is asserted during auto reset/restart operation.

2-43

PA 7300

PART II: OPERATION MANUAL

OUTPUT

FREQUENCY

DECELERATION TIME

ACCELERATION

TIME

HYSTERESIS

DETECTION LEVEL OF

STALL PREVENTION

DURING RUN

RETURN LEVEL

AC DRIVE OUTPUT

CURRENT

DETECTION TIME: 100ms

STALL PREVENTION DURING RUN

Summary of Contents for PA7300 Series



























































































































































Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands