TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 100

Page: 100 / 154

7 External baseblock (set value = 09)

• Baseblock is active when “open”. All other operations are the same as when set value = 8.

8 Accel/decel speed prohibit command (set value = 0A)

• As long as the accel/decel speed prohibit command is asserted, accel/decel speed is prohibited

and the output frequency at that time is held. When a stop command is asserted, the accel/decel

speed prohibit state is released and the system enters a stopped state. The ﬁgure below shows a

time chart.

Note: If the run command is asserted again after the stop command, while the accel/decel prohibit

command is inputed, the holding output frequency is stored unless the accel/decel prohibit command

is released. Therefore, operation is performed at the stored output frequency. Also when the power

supply is turned OFF in the accel/decel prohibit command input status, the holding output frequency

is still stored.

9 AC drive overheat alarm (set value = 0B)

• As long as an AC drive overheat signal is asserted, the “Over Heat OH2” blinks at the

digital operator.

10 UP command/DOWN command (set value = 10, 11)

• Acceleration/deceleration is performed by inputting the UP/DOWN commands without

changing frequency reference in the forward (reverse) run command input status, and

operation can be performed at a desired speed.

Set value = 10: UP command

Set value = 11: DOWN command

UP command

Closed

Open

Closed

DOWN command

Open

Closed

Open

Closed

Status

Accel (UP)

Decel(DOWN)

Hold

2-50

PA 7300

PART II: OPERATION MANUAL

FWD RUN

ACCEL/DECEL

SPEED PROHIBIT

COMMAND

FREQUENCY
REF.

OUTPUT FREQUENCY

Summary of Contents for PA7300 Series



























































































































































Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands