manualshive.com logo in svg

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Share
Download
TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 2

 

BEFORE INSTALLATION & USE

 

1  Ensure that the nameplate data corresponds with the application requirements. 

 

2.  Ensure that the product is undamaged.

 

WARNING

 

The following safety precautions must be observed:

 

1.  Electrical apparatus and incoming line supply can cause serious or fatal injury if the  

 

  product is improperly installed, operated, or maintained. Responsible personnel must  

 

  be fully trained to understand the hazards to themselves and others before being  

 

  involved in installing, operating, maintaining, and decommissioning electrical apparatus. 

 

  Particular industries and countries have further safety requirements. Refer to their trade  

 

  safety bodies, British Standards Institution, Dept. of Trade & Industry, etc., for further  

 

  information. In the USA, refer to NEMA MG2, the National Electrical Code, local  safety  

 

  requirements, etc.  European Union Safety information can be obtained from such as:

 

  BS4999; EN60204-11   

EN292-1 

EN294 

 

  IEE Wiring Regulations

 

2.  When servicing, all power sources to the product and accessory devices should be  

 

  de-energized and disconnected with all moving parts at standstill.

 

3.  Safety guards and other protective devices must be neither bypassed nor  

 

  rendered inoperative.

 

4.  The apparatus must be grounded. Refer to relevant standards such as EN60204-1, IEE 

 

  Wiring Regulation, etc.

 

5.  A suitable enclosure must be provided to prevent access to live parts. Extra caution  

 

  should be observed around apparatus that is automatically started, has automatic resetting  

 

  relays, or is remotely started. In the event that these starting means have not been properly  

 

  disabled, the apparatus could start unexpectedly.

 i

 

PA 7300

 

INSTRUCTION MANUAL

 

 

 

 

 

 

 

 

 

Summary of Contents for PA7300 Series



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands