TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 67

Page: 67 / 154

(15) Carrier frequency upper/lower limit, proportion gain (Cn-23 to Cn-25)

• The relationship between output frequency and carrier frequency is determined as

follows from the set values of Cn-23 to Cn-25.

(a)

For constant carrier frequency (set value of Cn-23):

• Set 0 in Cn-25 and set the same value in Cn-23 and Cn-24.

(b)

For variable carrier frequency: Carrier frequency changes according to Cn-23 to 25

set values and output frequency as shown below.

Invalid Fc (OPE11) is displayed in the following cases:

1 Cn-25 > 6 and Cn-24 > Cn-23

2 Cn-23 > 5kHz and Cn-24 ≤ 5 kHz

(16) Overtorque detection level (Cn-26)

• Set overtorque levels in units of 1%. AC drive rated current is regarded as 100%.

(17) Overtorque detection time (Cn-27)

•

Set overtorque detection times in units of 0.1 second.

(18) Stall prevention level during acceleration (Cn-28)

• Set stall prevention level during acceleration in units of 1%. AC drive rated current is

regarded as 100%.

(19) Stall prevention level during run (Cn-30)

• Set a level for stall prevention level during run in units of 1%. AC drive rated

current is regarded as 100%

• Stall prevention during run starts deceleration when the output current is greater than

the setting value of Cn-30 (stall prevention level during run) for during agreed frequency for

100ms or more. The AC drive decelerates as long as the output current exceeds the setting

value of Cn-30 (stall prevention level during run). When the output current goes below the

setting value, the AC drive reaccelerates. The deceleration time selected in the 4th digit of

Sn-10 is used.

• During stall prevention during run, stall prevention during deceleration and acceleration

are still enabled.

2-17

PA 7300

PART II: OPERATION MANUAL

Cn-23

Cn-24

FOUT×Cn-25×K

(

K: INTERNAL FIXED

CONSTANT

)

CARRIER
FREQUENCY

OUTPUT FREQUENCY

Summary of Contents for PA7300 Series



























































































































































Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands