manualshive.com logo in svg

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Share
Download
TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 111

 

11 

Control command (set value=A)

   

•  This contact is “closed” when the control command from the keyboard is selected.

 

12 

Overtorque detection (set value=B)

   

•  This contact remains “closed” as long as the AC drive is detecting overtorque. Set 

   

 

overtorque detection level in Cn-26 and set overtorque detection time in Cn-27.

 

13 

Frequency reference loss (set value=C)

   

•  This is “closed” when loss of frequency reference is detected.

 

14 

Not used (set value= D)

 

15 

Fault (set value=E)

   

•  This contact is “closed” when the AC drive detects a major fault. However, in the event 

   

 

of a fault in the watchdog (OP Commu. Error 1 CPF00) or transmission between the  

   

 

mainframe and operator, the AC drive does not operate.

 

16 

Not used (set value=F)

   

•  Set F in multi-function contact when the output is not used.

2-61

 

PA 7300

 

PART II: OPERATION MANUAL

Summary of Contents for PA7300 Series



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands