TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 126

Page: 126 / 154

3-4

PA 7300

PART II: OPERATION MANUAL

FAULT CONTACT

OUTPUT

ERROR CAUSES

ACTION TO BE TAKEN

Operation

Parameter setting error

• One of the AC Drive input phases are lost

• 3 phase power source is unbalanced.

• Check the AC Drive input power supply wiring.

Operation

• The main circuit smoothing capacitors have deteriorated.

• Check the capacitors.

• Improper input phase loss detection level (Cn-61) setting

• Check the setting of Cn-61.

Operation

• One of the AC Drive output phases are lost

• Check the wiring between AC Drive and motor.

• DCCT fault.

• Replace the DCCT.

Operation

• Motor load current is too large.

• Check the motor load current.

• The eﬀective cooling of motor is not suﬃcient.

• Check the motor eﬀective cooling.

Operation

• RS-485 communication option card fault

• Excess vibration or shock

• Turn oﬀ power, then turn on again. If error is

• External noise

persistent, replace the option card.

Operation

• The RS-485 communication protocols setting AC Drive

• Check the setting in Sn-24 and option card.

(Sn-24) and option card are inconsistent.

Operation

• PA-P card fault

• Turn oﬀ power, then turn on again. If error is

persistent, replace the option card

Operation

Summary of Contents for PA7300 Series



























































































































































Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands