TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 69

Page: 69 / 154

(23) Number of auto restart attempts (Cn-36)

• Set the number of auto reset/restart operations. Setting to zero causes no auto

reset/restart operation.

• Each time any OC, OV, OL1, OL2, OL3, OH, UV1, OC, GF, OV, rr or UV1 fault

occurs, the number of auto reset/restart operations is incremented by 1, and auto

reset/restart operation is performed according to the following procedure.

• Auto reset/restart operation sequence

1. When a fault is detected, the AC drive output is shut oﬀ for the minimum baseblock

time (Cn-40). During shut oﬀ of the drive output, a fault occurring in the operator

is displayed.

2. When the minimum baseblock time (Cn-40) elapses, the fault is automatically

reset, and speed search operation is performed with the output frequency at the

time of the fault.

3. When the total number of faults exceed the number of auto restart attempts (Cn-36),

automatic reset is not performed, and the AC drive output is shut oﬀ. At this time, fault

contact output is activated.

• The number of auto reset/restart operations is cleared to zero when:

1. No fault occurs for 10 minutes or more.

2. A fault reset signal is inputed from the control circuit terminals or the digital operator.

• Auto reset/restart operation is not performed in the following cases:

1. When operation not continued at momentary power loss (3rd digit of Sn-11=0) is

speciﬁed, UV1 fault is not automatically reset.

2. When OC or OV fault occurs due to external fault during deceleration stop or DC

injection braking stop, the AC drive output is shut oﬀ.

(24) Power loss ride-thru time (Cn-37)

• Set in units of 0.1 second. The initial value depends on the AC Drive’s capacity.

2-19

PA 7300

PART II: OPERATION MANUAL

Cn-40

SPEED

FAULT

DETECTION

FAULT
CONTACT

OUTPUT

FREQUENCY

MOTOR

SPEED

WHEN 2ND DIGIT OF

Sn-11=1,

FAULT CONTACT IS

OUTPUT.

Summary of Contents for PA7300 Series



























































































































































Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands