TECO-Westinghouse PA7300 Series Installation And Operation Manual Download Page 104

Page: 104 / 154

13 DC injection braking command (set value = 60)

• When DC braking command is asserted while the AC drive stops, DC braking operation is

performed. When operation signal or jog operation command is asserted, the DC braking

operation is stopped and the run or jog operation is started. (Privileged operation)

14 Search command (set value = 61,62)

• To start the motor during a coast when conditioning commercial power supply to the AC drive

transfer operation is performed, the motor can be operated without tripping by using the

speed search function.

Set value = 61: Speed search starts with the maximum frequency.

Set value = 62: Speed search starts with the frequency reference value when search

command is asserted.

• Search commands with set values of 61 and 62 cannot be set at the same time.

• By inputting the run command with the search command “closed” during baseblock,

speed search starts after shutting down the AC drive output for the minimum baseblock

time (Cn-40)

• Speed search operation starts when AC drive output current is larger than the set value

of the speed search operation level (Cn-38). The frequency at which the AC drive output current

is lower is determined as the speed synchronous point: Re-acceleration/deceleration is performed

in the set accel/decel time up to the set frequency.

2-54

PA 7300

PART II: OPERATION MANUAL

2-54

DC INJECTION

BRAKING

COMMAND

FWD RUN

COMMAND

OUTPUT

FREQUENCY

DC INJECTION

BRAKING

DC INJECTION

BRAKING START

FREQUENCY (Cn-

10)

DC INJECTION

BRAKING

Summary of Contents for PA7300 Series



























































































































































Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands

TECO-Westinghouse PA7300 Series, Installation And Operation Manual

Search results

Summary of Contents for PA7300 Series

Reviews:

Brands by name

Popular brands