6-9
6-9
TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
s a e p ,
e ey
us be
s a e p ,
e ey
us be
turned fully off to reset the ignition
turned fully off to reset the ignition
switch, allowing the B (Battery)
switch, allowing the B (Battery)
and S (Start) contacts to close.
and S (Start) contacts to close.
This is a momentary position that
This is a momentary position that
should only make contact when
should only make contact when
the key
the key
is fully
is fully
turned.
turned.
On the
On the
back of the ignition switch (S1,
back of the ignition switch (S1,
Illustration 6-6), at the B terminal,
Illustration 6-6), at the B terminal,
you should see 12 VDC straight
you should see 12 VDC straight
from the battery.
from the battery.
Turn
Turn
the key
the key
to
to
the start
the start
position.
position.
On the
On the
back of
back of
the ignition switch (S1), at the S
the ignition switch (S1), at the S
terminal, you should see 12 VDC,
terminal, you should see 12 VDC,
if not, remove the wire from the S
if not, remove the wire from the S
terminal.
terminal.
Turn
Turn
the ignition
the ignition
switch
switch
(S1) to the start position and
(S1) to the start position and
recheck for 12 VDC at the S termi-
recheck for 12 VDC at the S termi-
nal.
nal.
If the
If the
12 VDC is
12 VDC is
now present,
now present,
the wire, just removed, is shorted.
the wire, just removed, is shorted.
Isolate and
Isolate and
remove the
remove the
short.
short.
If
If
12 VDC is not present and 12
12 VDC is not present and 12
(continued)
(continued)
C
C
o
o
m
m
p
p
o
o
n
n
e
e
n
n
t
t
P
P
r
r
o
o
b
b
l
l
e
e
m
m
C
C
o
o
r
r
r
r
e
e
c
c
t
t
i
i
o
o
n
n
4.
4.
Ig
Ig
ni
ni
ti
ti
on
on
Sw
Sw
it
it
ch
ch
(Continued)
(Continued)
(Continued)
(Continued)
VDC was present at the B termi-
VDC was present at the B termi-
nal, replace the ignition switch
nal, replace the ignition switch
(S1).
(S1).
5
5
.
.
W
W
i
i
r
r
e
e
s
s
1
1
.
.
W
W
i
i
r
r
e
e
h
h
a
a
s
s
l
l
o
o
s
s
t
t
c
c
o
o
n
n
t
t
i
i
n
n
u
u
i
i
t
t
y
y
.
.
1
1
.
.
I
I
s
s
o
o
l
l
a
a
t
t
e
e
t
t
h
h
e
e
w
w
i
i
r
r
e
e
f
f
r
r
o
o
m
m
t
t
h
h
e
e
c
c
i
i
r
r
c
c
u
u
i
i
t
t
(Ohm out
(Ohm out
the wire).
the wire).
Ohms will
Ohms will
vary according to the length of the
vary according to the length of the
wire.
wire.
Expect to
Expect to
see low
see low
Ohms if
Ohms if
wire is good.
wire is good.
https://www.forkliftpdfmanuals.com/
Summary of Contents for TX180S
