Taylor TX180S, Maintenance Manual

Page: 21 / 320

TX / TXH / TXB 180S - 400L (Rev. 4/23/07) TX / TXH / TXB 180S - 400L (Rev. 4/23/07) 1-4 1-4
Illustration 1-4. Illustration 1-4. Engine Engine Diagnostics Diagnostics Icons Icons
Calibration Of Electronic Accelerator Pedal To Calibration Of Electronic Accelerator Pedal To
ECM Of Engine. ECM Of Engine. The The Cummins Cummins QSB6.7 QSB6.7 engine engine
uses an electronic accelerator to control engine uses an electronic accelerator to control engine
speed. speed. Each time Each time the accelerator the accelerator pedal is pedal is
changed, disconnected and the ignition switch is changed, disconnected and the ignition switch is
turned on, or ECM (Electronic Control Module) is turned on, or ECM (Electronic Control Module) is
changed out, the accelerator pedal must be cali- changed out, the accelerator pedal must be cali-
brated to brated to the ECM. the ECM. Calibration procedures Calibration procedures are as are as
follows: follows:
1. 1. Appl Appl y the p y the p ark ark ing b ing b rak rak e, pl e, pl ace t ace t he sh he sh ift ift er in er in
neutral, and turn the ignition switch to the Igni- neutral, and turn the ignition switch to the Igni-
tion position (first click). tion position (first click).
2. 2. Cycle Cycle the the accel accel erator erator pedal pedal throu throu gh i gh i ts ts full full
range of travel three times. range of travel three times.
3. 3. Tur Tur n the n the ignit ignit ion sw ion sw itch itch to th to th e Off e Off positi positi on fo on fo r r
at least 30 seconds. at least 30 seconds.
Engine Fault Code Warning Box Engine Fault Code Warning Box (Illustration (Illustration
1-5) 1-5) . . An engine fault An engine fault code warning box code warning box will be dis- will be dis-
played on the Engine Information screen when an played on the Engine Information screen when an
engine fault code engine fault code is active. is active. This warning box This warning box dis- dis-
plays the number of plays the number of the active fault code. the active fault code. T T o clear o clear
the warning box after recording the fault code the warning box after recording the fault code
number, depress number, depress the F2 (OK) the F2 (OK) button. button. Once the Once the
warning box has been cleared, the fault code will warning box has been cleared, the fault code will
have to be flashed out in the Diagnostic Mode if it have to be flashed out in the Diagnostic Mode if it
was not recorded (refer to was not recorded (refer to Diagnostic Fault Diagnostic Fault
Codes Codes ). ).
Engine Diagnostic Icons Engine Diagnostic Icons (Illustration 1-4) (Illustration 1-4) . . The The
engine diagnostic icons, displayed by the Taylor engine diagnostic icons, displayed by the Taylor
Integrated Control System (TICS) display module Integrated Control System (TICS) display module
on the Engine Information Screen, are used to on the Engine Information Screen, are used to
alert the operator of engine related problems. alert the operator of engine related problems.
Each diagnostic icon’s function is described as Each diagnostic icon’s function is described as
follows: follows:
1. 1. Yellow Icon Yellow Icon (System Fault) (System Fault) . . This icon will be This icon will be
displayed during a displayed during a non-fatal system non-fatal system error. error. The The
engine can still be run, but the fault should be engine can still be run, but the fault should be
corrected as soon as possible. corrected as soon as possible.
NOTE: NOTE: In the In the diagnostic mode, diagnostic mode, the yellow the yellow icon icon
will flash after the red icon completes the three- will flash after the red icon completes the three-
digit fault code. digit fault code.
2. 2. Red Icon Red Icon (Engine Shutting Down) (Engine Shutting Down) . . This This icon icon
will be displayed when the engine needs to be will be displayed when the engine needs to be
shut off before permanent damage occurs to shut off before permanent damage occurs to
the engine. the engine. Should the Should the red icon red icon be displayed be displayed
while operating, the fault can be engine disab- while operating, the fault can be engine disab-
ling after ling after approximately 32 approximately 32 seconds. seconds. Should Should
the engine shut down due to the severity of the engine shut down due to the severity of
the fault, it can be restarted and will run for the fault, it can be restarted and will run for
approximately 32 approximately 32 seconds. seconds. The engine The engine will will
run for approximately 32 seconds each time it run for approximately 32 seconds each time it
is restarted. is restarted. There are no There are no limits on limits on the num- the num-
ber of times the engine may be restarted. ber of times the engine may be restarted.
NOTES: NOTES:
  The engine should be shut off as soon as it The engine should be shut off as soon as it
can be shut off can be shut off safely safely . . The engine should The engine should not not
be run until be run until the fault is corrected. the fault is corrected.
 
This icon is also used to flash out the fault This icon is also used to flash out the fault
code number in the diagnostic mode. code number in the diagnostic mode.
https://www.forkliftpdfmanuals.com/