Sunny Boy 700 Technical Description Download Page 72

Page: 72 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

9 Technical Data

Input variables (PV modules)

Maximum open circuit voltage of the PV strings

It is essential to check if the PV modules produce a voltage within the

specified tolerable input voltage range in their rated temperature range.

The maximum open circuit voltage of the connected PV string may not

exceed the specified maximum DC input voltage.

The open circuit voltage of the PV panel depends on its cell temperature as well as

solar radiation. The maximum open circuit voltage of the PV panel is reached at the

lowest cell temperature. Therefore when planning a PV plant take into account the

lowest possible ambient temperature of the PV panel. Based on this temperature the

maximum open-circuit voltage of the PV panel can be calculated if the type of PV

module is known. You can enter these data into our EXCEL

file “GenAu” and check

whether the maximum admissible input voltage of the Sunny Boy is not exceeded in

any possible operating state. You will find this tool in the Internet for download at:

http://www.sma.de/ftp/energietechnik/sunnyboy/GenAu/GenAu.exe.

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 72 / 85

Search results

Summary of Contents for 700

Reviews: