Sunny Boy 700 Technical Description Download Page 63

Page: 63 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

Sunny Data Control

Large PV-plants with numerous Sunny Boys are supervised and monitored with a

Sunny Boy Control. The Sunny Boy Control handles central measurement data ac-

quisition and diagnosis for up to 50 Sunny Boys and assists the commissioning of the

PV-plant. Additional features are remote diagnosis via modem and fax messages.

For global visualization of PV plant data SMA offers the Sunny Data Control PC soft-

ware under Windows. E.g. the power output of the entire large-scale PV-plant can be

shown in a matrix.

For the numerous possibilities of establishing a monitoring concept with Sunny Boy

Control please see the Sunny Boy Control manual.

Device field

Information on
single device

Short information

Fig. 6.8: Sunny Data Control graphic user interface

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 63 / 85

Search results

Summary of Contents for 700

Reviews: