manualshive.com logo in svg

Sunny Boy 700, Technical Description, Page: 65 / 85

Share
Download
Sunny Boy 700 Technical Description Download Page 65

Sunny Boy 700 

 

Technical Description 

SB700-11:EE  

- 

65

 - 

SMA Regelsysteme GmbH

 

Status Messages 

Stop 

manual system stop 

Offset 

offset calibration of the electronics 

Warten 

grid conditions are not fulfilled (yet) 

Netzueb. 

checking grid (grid impedance) 

Zuschalt electronics 

are connecting to grid 

MPP-Such 

PV voltage is determined and set 

MPP 

Sunny Boy is in MPP mode 

U-Konst. 

Sunny Boy is in constant voltage mode 

Derating 

Reduction of current fed to the grid 

Stoer. failure 

 

Error messages  

F-Bfr-Srr communication 

between 

microcontrollers is failing 

F-EEPROM 

EEPROM cannot be read or written in 

F-EEPROM dBh EEPROM cannot be read or written in 

F-Fac-Bfr BFR-frequency 

measurement 

- value out of tolerable range 

F-Fac-Srr 

SSR-frequency measurement - value out of tolerable range 

F-dZac-Bfr 

BFR-sudden change of impedance - value out of tolerable range 

F-dZac-Srr 

SSR-sudden change of impedance - value out of tolerable range 

F-Imax internal 

overcurrent 

F-NUW-UAC 

different values between BFR and SRR for grid voltage  

F-NUW-FAC 

different values between BFR and SRR for grid frequency 

F-NUW-Mess 

different values between BFR and SRR for Vac, fac and Zac 

K1-Schliess 

Relay test failed 

K1-Trenn 

Relay test failed 

F-NUW-ZAC 

different values between BFR and SRR for grid impedance 

F-Offset 

Offset check for grid voltage or power measurement failed 

F-Rechner 

BFR or SSR controller failure  

F-Riso isolation 

resistance out of tolerable range 

F-Uac-Bfr 

BFR-grid voltage measurement - value out of tolerable range 

F-Uac-Srr 

SSR-grid voltage measurement - value out of tolerable range 

Summary of Contents for 700






















































































Reviews:

No comments