Sunny Boy 700 Technical Description Download Page 16

Page: 16 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

3 Installation

The installation of the Sunny Boy string inverter must be done by

qualified personnel that is approved by the local electricity company.

Make sure that all instructions in this chapter are followed.

Follow all safety regulations and regulations of the local electricity

company.

3.1 What must be done in case of transport damages?

The inverters are thoroughly checked before they are shipped. Even though they are

delivered in a sturdy packaging (which can be recycled) the inverters can be dam-

aged in transit, which is usually the forwarder’s fault.

Please inspect your inverter thoroughly after it is delivered. If any damages can be

detected on the packaging that could make you conclude the contents is damaged or

if you detect that the inverter is damaged please immediately notify the forwarding

company.

SMA or your local supplier can help you in this matter. In any case a declaration of

transport damage must be made within 6 days upon receipt of the product and must

be stated in writing directly to the forwarding agent. If it is necessary to return the

inverter to the manufacturer please use the packaging the inverter was sent in.

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 16 / 85

Search results

Summary of Contents for 700

Reviews: