Sunny Boy 700 Technical Description Download Page 49

Page: 49 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

6 System Monitoring and Diagnosis

6.1 Data Transmission via Powerline

Signal transmission between the Sunny Boy and the Sunny Boy Control or the PC is

done with the grid connection via Powerline. This requires a minimum of installation

(see below). The Sunny Boy must be equipped with a Powerline modem for data

transmission. The PC must be equipped with the socket modem (SWR-COM). This is

already integrated in the Sunny Boy Control, the specific controller for PV-plants. The

PC or the Sunny Boy Control can be positioned anywhere within the in-house net-

work as they acquire data directly from the AC circuit.

For trouble-free operation the Sunny Boys and the PC socket modem or the Sunny

Boy Control must be connected to the same phase of the in-house network. If the

communicating partners are connected to different phases the communication must

be established with a so-called phase coupling device. The phase coupling device is

available from SMA and must be installed by qualified personnel. It will make com-

munication within the entire in-house network possible.

Sunny Boy

RS232,
modem

Sunny Boy

Control

SWR-COM

Sunny Boy

Control

Powerline

Fig. 6.1: Example of data transmission via Powerline

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 49 / 85

Search results

Summary of Contents for 700

Reviews: