manualshive.com logo in svg

Sunny Boy 700, Technical Description, Page: 60 / 85

Share
Download
Sunny Boy 700 Technical Description Download Page 60

Sunny Boy 700 

 

Technical Description 

SB700-11:EE  

- 

60

 - 

SMA Regelsysteme GmbH

 

Follow ESD protection countermeasures when modifying the Sunny Boy: 

Electronic components are sensitive to electrostatic discharge. To protect them you 

have to be on the same electric potential. Discharge the electrostatic charge by 

touching the grounded case before touching an electronic component, otherwise you 

take a great risk in destroying your electronics. 

Open the device as described in chapter 5.1. 

Remove the piggy back that is installed on the system control board. 

• 

Only for installation of an RS232 or RS485 board: 

− 

Remove the resistors (Fig. 6.6) on the system control board by cutting 

them out with a wire cutter. 

• 

Only for installation of a board for Powerline Communication: 

− 

Please make sure that the resistors (Fig. 6.6) are plugged onto the system 

control board. If not, resistors (corresponding to 0 Ohm resistors) have to 

be installed in there. 

Plug the desired piggy back module onto the required slot. When plugging on the 

piggy back please make sure no socket of the piggy back plug-in contacts remains 

open.  

Connect  the cables for RS232 (see Fig. 6.3) or RS485 (see Fig. 6.6). No cabling is 

necessary for Powerline communication. Data cables are lead outside through the 

free opening at the bottom of the Sunny Boy. Please insert the PG16 screws into this 

opening and fasten them.  

Summary of Contents for 700






















































































Reviews:

No comments