Sunny Boy 700 Technical Description Download Page 46

Page: 46 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

5.1 Opening and closing of the Sunny Boy

Normally the Sunny Boy operates fully automatically and maintenance-free. Should

the device nonetheless be opened e.g. for

•

upgrading or modification of the Sunny Boy interface

•

control of internal fuse

•

analysis of earth fault indication

•

setting up the input voltage range

follow the instructions given below.

Opening of the Sunny Boy

The Sunny Boy must only be opened by a qualified electrician.

When working on the Sunny Boy follow the instructions below:

1. Separate the Sunny Boy from the grid by opening the circuit breaker.

2. Separate all poles of the Sunny Boy from the PV-panel by pulling the MC plug

connectors.

Wait for approx. 5 minutes until internal voltage has discharged.

3. Open the Sunny Boy in the following order.

4. Take off the lid by removing screws 1-4 (see Fig. 5.2 on page 47) on the lid (M5).

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 46 / 85

Search results

Summary of Contents for 700

Reviews: