Sunny Boy 700 Technical Description Download Page 64

Page: 64 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

6.5 Measuring Channels and Messages of the Sunny Boy

If your PC is equipped with communication (see chapter 2.2), it supports a number of

measuring channels and messages from the Sunny Boy inverters and transmits them

to the output unit for diagnosis.

The following abbreviations are used:

BFR

Betriebsführungsrechner (Sequential Control System)

SRR

Stromregelungsrechner (Current Control System)

Measuring Channels

Upv-Ist PV-input

voltage

Upv-Soll

PV-desired voltage of the internal Upv-control

Iac-Ist

current to the grid

Uac grid

voltage

Fac grid

frequency

Pac

power fed to grid

Zac grid

impedance

Riso

isolation resistance

Ipv

current from PV-panels

E-Total energy

yield

h-Total

total operation hours

Netz-Ein

total system start ups

Seriennummer Sunny

Boy serial number

Status status

Fehler

failure description for status “failure“

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 64 / 85

Search results

Summary of Contents for 700

Reviews: