Sunny Boy 700 Technical Description Download Page 51

Page: 51 / 85

Sunny Boy 700

Technical Description

SB700-11:EE

SMA Regelsysteme GmbH

6.2 Data Transmission with a Separate Data Cable

RS232 communication is only suitable for data transmission between a

PC and one single Sunny Boy.

Data transmission via Powerline is a reliable and affordable solution. In electrical

grids which are strongly influenced by high-frequency disturbance such as those in

industrial sites data transmission via Powerline may not be possible. Communication

between the Sunny Boys and the Sunny Boy Control or the PC can then be done

with a separate data cable.

RS232 communication

If only one Sunny Boy has to be connected to the PC the easiest way is direct cou-

pling via an RS232 port. A maximum of 15 m is permissible between the PC and the

Sunny Boy.

Single

Sunny Boy

RS 232

Electricity Grid

Fig. 6.2: Example for RS232 communication with a single Sunny Boy

RS232 communication with a Sunny Boy is only a reasonable solution

with direct connection to the PC.

If a Sunny Boy Control is used instead of the PC an RS485 connection is

necessary. See section “RS485 communication” for details.

Summary of Contents for 700






















































































Search results

Summary of Contents for 700

Reviews:

Sunny Boy 700, Technical Description, Page: 51 / 85

Search results

Summary of Contents for 700

Reviews: