Sun Microsystems StorEdge T3+ Service Manual Download Page 230

Page: 230 / 240

Glossary-2

Sun StorEdge T3 and T3+ Array Field Service Manual • September 2001

command-line interface

(CLI)

The interface between the Sun StorEdge T3 array’s pSOS operating system and
the user in which the user types commands to administer the array.

controller unit

A Sun StorEdge T3 array that includes a controller card. It can be use as a
standalone unit or configured with other Sun StorEdge T3 arrays.

expansion unit

A Sun StorEdge T3 array without a controller card. It must be connected to a
Sun StorEdge T3 array to be operational.

erasable programmable

read-only memory

(EPROM)

Memory stored on the controller card; useful for stable storage for long periods
without electricity while still allowing reprogramming.

Fibre Channel-

Arbitrated Loop

(FC-AL)

A 100 MB/sec serial channel, which allows connection of multiple devices
(disk drives and controllers).

field-replaceable unit

(FRU)

A component that is easily removed and replaced by a field service engineer or
a system administrator.

gigabit interface

converter (GBIC)

An adapter used on an SBus card to convert fiber-optic signal to copper.

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands