Sun Microsystems StorEdge T3+ Service Manual Download Page 83

Page: 83 / 240

Chapter 4

Controller Card Assembly

4-13

3. Reset the controller and press any key on the console when the system prompt

appears (within three seconds).

4. Set the bootmode and tftp settings as follows:

Where

xxx.xxx.xxx.xxx

is the host IP address.

5. Reset the T3+ system with the

reset -y

command.

6. Press a key from a serial port connection when the system prompts to press a key

within three seconds.

7. Install the firmware using the .

ep netload1

command.

8. Set the bootmode to automatic.

9. Power cycle the array to reset it.

a. Type:

b. Press the power button on each power and cooling unit to remove AC power.

c. Press the power buttons again to return AC power to the array.

T3B-EP> set bootmode tftp

T3B-EP> set tftphost

xxx.xxx.xxx.xxx

T3B-EP> reset -y

T3B-EP> .ep netload1

level-1_image_filename

T3B-EP> set bootmode auto

:/:<4> shutdown

shutdown the system, are you sure? [N] : y

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands