Sun Microsystems StorEdge T3+ Service Manual Download Page 166

Page: 166 / 240

10-2

Sun StorEdge T3 and T3+ Array Field Service Manual • September 2001

10.1.1

Preparing the Arrays

1. Decide which unit is the master controller and which is the alternate master.

2. Back up the data on both arrays.

Caution –

Make sure you back up data on both units before proceeding! You need to

re-create the volume(s) on the alternate master after cabling the units together.

3. Ensure that the data path between the host and both arrays has been quiesced.

There must not be any I/O activity.

4. Start a Telnet session with both arrays.

a. On the host, use the

telnet

command with the array name (or IP address) to

connect to the array.

b. Log in to the array by typing

root

and your password at the prompts.

The array prompt is displayed.

5. Verify that firmware levels for all array firmware are the same on the master unit

and alternate master unit.

On both arrays:

a. Type

ver

to display the controller firmware level.

For example:

In this example, the controller firmware level is listed as

Release

1.14

# telnet

array_name

Trying 129.150.47.101...

Connected to 129.150.47.101.

Escape character is ’^]’.

pSOSystem (129.150.47.101)

:/:<1> ver

T300 Release 1.14 2000/08/01 10:43:22 (129.150.47.135)

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands