Sun Microsystems StorEdge T3+ Service Manual Download Page 200

Page: 200 / 240

B-2

Sun StorEdge T3 and T3+ Array Field Service Manual • September 2001

B.2

System Defaults

Specify system defaults with the

sys

command. See the Sun StorEdge T3 and T3+

Array Administrator’s Guide for more information on using the

sys

command.

tftpfile

value

Boot code file identification number (39 character
maximum)

hostname

machinename

Machine name of the Sun StorEdge T3 host machine (39
character maximum)

vendor

vendorname

Name of manufacturer or vendor

model

modelnumber

Controller model number (set at EP level)

revision

nnn

Controller EP revision (EP writes this value)

logto

[1 | * | filename] where:
1=Forces logging to serial console
*=Directs logging daemon to direct logging as specified
in the

/etc/syslog.conf

file.

loglevel

[0|1|2|3|4-] where:
0=No logging at all
1=Error messages only
2=Warning and higher messages
3=Notice and higher messages
4=All message levels including info

rarp

[on | off]

mac

n:n:n:n:n:n

Controller MAC address. Set by firmware

TABLE B-2

System Default Settings

Sys Parameter

Default

Variables

blocksize

64k

[16k | 32k | 64k]

cache

auto

[auto|writebehind|writethrough|off]

mirror

auto

[auto | off]

mp_support

none

[rw | none] Multi-pathing support

rd_ahead

Set to off to always perform datablock read ahead.

TABLE B-1

Default Settings—

set

List

Parameter

Default

Variables

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands