Sun Microsystems StorEdge T3+ Service Manual Download Page 233

Page: 233 / 240

Glossary-5

redundant array of

independent disks

(RAID)

A configuration in which multiple drives are combined into a single virtual
drive, to improve performance and reliability.

Simple Network

Management Protocol

(SNMP)

A protocol for remotely managing a computer network.

synchronous dynamic

random access memory

(SDRAM)

A form of dynamic random access memory (DRAM) that can run at higher
clock speeds than conventional DRAM.

system area

Located on the disk drive label, the space that contains configuration data, boot
firmware, and file system information.

uninterruptable power

source (UPS)

A component within the power and cooling unit. The UPS supplies power
from a battery in the case of an AC power failure.

unit interconnect card

(UIC)

See Interconnect Card.

volume

Also called a logical unit number (LUN), a volume is one or more drives that
can be grouped into a unit for data storage.

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands