Sun Microsystems StorEdge T3+ Service Manual Download Page 232

Page: 232 / 240

Glossary-4

Sun StorEdge T3 and T3+ Array Field Service Manual • September 2001

master unit

The main controller unit in a partner group configuration.

media access control

(MAC) address

A unique address that identifies a storage location or a device.

media interface adapter

(MIA)

An adapter that converts fiber-optic light signals to copper.

megabyte (MB or

Mbyte)

One megabyte is equal to one million bytes (1x106).

megabytes per second

(MB/sec)

A performance measurement of the sustained data transfer rate.

parity

Additional information stored with data on a disk that enables the controller to
rebuild data after a drive failure.

partner group

A pair of interconnected controller units. Expansion units interconnected to the
pair of controller units can also be part of the partner group.

power and cooling

unit

A FRU component in the Sun StorEdge T3 array. The unit contains a power
supply, cooling fans, and an integrated UPS battery. A Sun StorEdge T3 array
contains two power and cooling units.

pSOS

A real-time operating system used as the primary operating system for the Sun
StorEdge T3 array.

read caching

Data for future retrieval, to reduce disk I/O as much as possible.

reliability, availability,

serviceability (RAS)

Product features that include high availability, easily serviced components that
are very dependable.

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands