Sun Microsystems StorEdge T3+ Service Manual Download Page 99 | Manualshive

Page: 99 / 240

background image

Chapter 5

Disks and Drives

5-13

5.4

Upgrading Disk Drive Firmware

The latest disk drive firmware versions are located on the SunSolve web site:

http://sunsolve.sun.com

During a disk drive firmware download, the functionality of the array is limited. To
avoid system problems, verify that:

■

A current backup copy of array data exists.

■

The data path to the host has been quiesced. There must not be any
I/O activity during the disk drive firmware download.

■

The Ethernet connection is not being used for any other operation during this
procedure. If Component Manager is being used to monitor the array, disable the
automatic polling utility. Refer to the current Sun StorEdge Component Manager
Users Guide for instructions to disable polling.

Caution –

If a host-mounted utility program such as Component Manger is actively

polling, problems might occur during the firmware download. Disable the polling
utility within Component Manager during this procedure to avoid problems.

■

No unnecessary command line program interaction with the array is performed
during the disk drive firmware download.

Note –

The disk firmware download takes approximately 20 minutes for 9 drives.

Do not attempt to interrupt the download or perform other command-line functions
during the process. The command prompt reappears after the download process has
completed.

To upgrade the firmware:

1. Use

ftp

to transfer the firmware to the array

root

directory in binary mode.

See Section 2.3, “Establishing an FTP Session” on page 2-5 for additional
information.

Note –

The file name of files being transferred to the local disk must be 12

characters or less in size and start with an alphabetic character (not numeric).

2. Establish a Telnet connection to the array.

See Section 2.2, “Establishing a Telnet Session” on page 2-3.

«
...
97
98
99
100
101
...
»

Summary of Contents for StorEdge T3+

















































































































































































































































Reviews:

No comments

Related manuals for StorEdge T3+

Brand: Cambridge SoundWorks Pages: 20

Brand: iDance Pages: 13

Brand: Naxa Pages: 3

instant theatre KIT100

Brand: KEF Pages: 48

Brand: Panasonic Pages: 89

Brand: M&K Sound Pages: 15

Brand: M-Audio Pages: 30

GreenSpec HTHB-HVRGRN

Brand: Halsey Taylor Pages: 7

Brand: K&F Pages: 28

Brand: Panasonic Pages: 16

Brand: Power Acoustik Pages: 5

Brand: Vonyx Pages: 16

Nucleus Reference 3.5

Brand: Anthony Gallo Acoustics Pages: 20

NS-R2111 - Simulated Rock Outdoor Speakers Speaker

Brand: Insignia Pages: 2

YL Powership MMA-250FI

Brand: Youly Electric Pages: 16

Wi-Corporate Controller

Brand: GSD Pages: 14

Brand: KEF Pages: 16

Brand: Amphion Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands