Sun Microsystems StorEdge T3+ Service Manual Download Page 229 | Manualshive

Page: 229 / 240

background image

Glossary-1

Glossary

A

administrative

domain

Partner groups (interconnected controller units) that share common
administration through a master controller.

alternate master unit

The secondary array unit in a partner group that provides failover capability
from the master unit.

alternate pathing

(AP)

A mechanism that reroutes data to the other array controller in a partner group
upon failure in the host data path. Alternate pathing requires special software
to perform this function.

auto cache mode

The default cache mode for the Sun StorEdge T3 array. In a fully redundant
configuration, cache is set to write-behind mode. In a nonredundant
configuration, cache is set to write-through. Read caching is always performed.

auto disable

The Sun StorEdge T3 array default that automatically disables a disk drive that
has failed.

auto reconstruction

The Sun StorEdge T3 array default that automatically reconstructs data onto a
new disk drive from one of the other drives.

B

buffering

The process of data transfer between the host and the drives.

«
...
227
228
229
230
231
...
»

Summary of Contents for StorEdge T3+

















































































































































































































































Reviews:

No comments

Related manuals for StorEdge T3+

ACTIVE REFLEX 300A II Series

Brand: Magnat Audio Pages: 28

Brand: Abus Pages: 4

Brand: JBL Pages: 10

BellRFID MX-Bell1-Core

Brand: Mobotix Pages: 2

Brand: Q-See Pages: 13

Brand: Vizio Pages: 24

IOLAN SDG1 LA/LE

Brand: Perle Pages: 21

Brand: Sinotec Pages: 2

Brand: LSS Pages: 14

Brand: Lynx Pages: 14

Brand: Nelson Pages: 142

Traveler 00076037

Brand: Hama Pages: 7

Brand: QSC Pages: 10

Brand: Geberit Pages: 356

Brand: Wave Pages: 2

Brand: NAIM Pages: 51

Access 1 165 CA1

Brand: Focal Pages: 1

Brand: System Sensor Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands