Sun Microsystems StorEdge T3+ Service Manual Download Page 71 | Manualshive

Page: 71 / 240

background image

4-1

C H A P T E R

4

Controller Card Assembly

This chapter describes how to monitor and replace the controller card and how to
upgrade the firmware. The chapter contains the following sections:

■

Section 4.1, “Controller Card LEDs” on page 4-1

■

Section 4.2, “Removing and Replacing a Controller Card” on page 4-4

■

Section 4.3, “Upgrading Controller Firmware” on page 4-5

4.1

Controller Card LEDs

The controller card LEDs for a Sun StorEdge T3 array differ from that of a Sun
StorEdge T3+ array. The controller LEDs of both array models are described in the
following sections.

Sun StorEdge T3 Array Controller LEDs

The Sun StorEdge T3 array controller card has a channel-active LED for the host
interface port, a controller status (online) LED, and a reset switch.

TABLE 4-1

lists the

possible states of the channel-active LED and describes each state.

TABLE 4-2

lists the

possible states and descriptions for the controller status LED.

«
...
69
70
71
72
73
...
»

Summary of Contents for StorEdge T3+

















































































































































































































































Reviews:

No comments

Related manuals for StorEdge T3+

Brand: JBL Pages: 7

Brand: Eagletone Pages: 2

Brand: Fender Pages: 18

Brand: JBL Pages: 7

Brand: National Comfort Products Pages: 28

Brand: NatComm Pages: 16

Brand: T+A Pages: 2

Brand: Blaupunkt Pages: 11

Brand: Subpac Pages: 15

Brand: CABASSE Pages: 16

125.032, 125.063

Brand: Vonyx Pages: 16

Brand: Velleman Pages: 55

Brand: Bayrol Pages: 56

Brand: Steren Pages: 6

Brand: Beta Three Pages: 10

WK MIG 5040 F SYNERGIC

Brand: WELDKAR Pages: 84

Brand: iLive Pages: 8

Brand: Jensen Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands