Sun Microsystems StorEdge T3+ Service Manual Download Page 113

Page: 113 / 240

Chapter 7

Power and Cooling Unit Assemblies

7-3

7.2.1

Power and Cooling Unit LEDs

Each power and cooling unit has an AC LED and a power-supply (PS) LED.

TABLE 7-1

lists the possible conditions of these LEDs and describes each state.

FIGURE 7-2

Power and Cooling Unit LEDs

TABLE 7-1

Power and Cooling Unit LED Descriptions

AC LED (Green
or Amber)

PS LED
(Green or Amber)

Description

Off

• Power is off
• No AC input

Amber

Off

• Power is off
• Power switch turned off
• AC power is available

Green

Off

Occurs when array is shut down:
• PCU disabled
• AC power is available

Green

Normal operating state:
• PCU receiving AC power
• Power switch is turned on
• AC power is available

Amber

• Switch is off. Array powers off after PCU is
disabled

AC LED

PS LED

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands