Sun Microsystems StorEdge T3+ Service Manual Download Page 73 | Manualshive

Page: 73 / 240

background image

Chapter 4

Controller Card Assembly

4-3

Sun StorEdge T3+ Array Controller Card LEDs

The Sun StorEdge T3+ array controller card has two channel-active LEDs, one for the
FC-AL interface port and one for the Ethernet port, and a controller status (online)
LED.

TABLE 4-3

lists the possible states of the controller card LEDs and describes each

state.

FIGURE 4-2

Sun StorEdge T3+ Array Controller Card LEDs

TABLE 4-3

Sun StorEdge T3+ Array Controller Card LED Descriptions

LED

Action

Description

FC-AL Channel
Active LED
(green)

Off

Port disabled

Green

Port enabled and idle

Blinking green

Port enabled and active

Ethernet Active LED
(green)

Off

Link invalid

Green

Link valid and idle

Blinking green

Link valid and active

10/100 BASE-T
Active LED (green)

Off

Port disabled (10 Mbps rate)

Green

Port enabled and idle (100 Mbps
rate)

Blinking green

Port enabled and active

Controller Status LED
(green or amber)

Off

Controller not installed (not
recognized)

Green

Controller OK

Amber

Controller boot, shutdown, or
firmware download in progress

Blinking amber

Controller failure; OK to replace
controller

Note—Verify a controller card failure using the CLI or Sun StorEdge Component Manager.

Ethernet

Controller online
status LED

10/100BASE-T
active LED

FC-AL active LED

active LED

«
...
71
72
73
74
75
...
»

Summary of Contents for StorEdge T3+

















































































































































































































































Reviews:

No comments

Related manuals for StorEdge T3+

Brand: Mackie Pages: 14

Brand: Samsung Pages: 34

Brand: 2N Pages: 21

Brand: 2N Pages: 23

Brand: ZKTeco Pages: 16

Brand: Audio System Pages: 2

Brand: Displays2go Pages: 3

BTS 1MB / 37329

Brand: Vivanco Pages: 20

Brand: Neptune Pages: 35

Brand: Peavey Pages: 4

Brand: Qvis Pages: 32

Brand: MRC Pages: 2

Brand: Aaron Pages: 2

Brand: Aaron Pages: 1

Brand: Battery Watering Technologies Pages: 2

Brand: APART Pages: 28

Brand: Amico Pages: 4

CIRFLEXX UMS 4100

Brand: Grundig Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands