Sun Microsystems StorEdge T3+ Service Manual Download Page 95

Page: 95 / 240

Chapter 5

Disks and Drives

5-9

4. Use a coin or small screwdriver to press in and release the drive latch handle.

FIGURE 5-4

Releasing the Latch Handle

5. Use the latch handle to slowly pull the disk drive out 1 inch (2.5 cm).

Wait 30 seconds, and then pull the drive out completely. This gives the disk drive
time to spin down.

6. Remove the disk drive from the array. See

FIGURE 5-5

Push in the latch handle on the removed disk drive to protect it from damage.

Caution –

Any disk drive that is removed must be replaced within 30 minutes or

the Sun StorEdge T3 and T3+ array and all attached arrays will automatically shut
down and power off.

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands