Sun Microsystems StorEdge T3+ Service Manual Download Page 96

Page: 96 / 240

5-10

Sun StorEdge T3 and T3+ Array Field Service Manual • September 2001

FIGURE 5-5

Removing a Disk Drive

7. Release the latch handle on the disk drive to be installed.

8. Insert the new disk drive gently on the middle of the rails and push it in until it

is seated with the centerplane connector.

Use a coin or small screwdriver to press in and lock the latch handle.

9. Replace the front panel.

Note –

Replace the front panel for the array to meet FCC compliance requirements.

10. Type

fru list u

n to verify the firmware revision of the new disk drive,

where:

■

n is the unit (

) number (n)

■

is the drive (

) number(n).

See Section 5.4, “Upgrading Disk Drive Firmware” on page 5-13,” for instructions, if
necessary.

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands