Sun Microsystems StorEdge T3+ Service Manual Download Page 201

Page: 201 / 240

Appendix B

Sun StorEdge T3 Array System Defaults

B-3

B.3

Volume Defaults

Specify system defaults with the

vol

command. See the Sun StorEdge T3 and T3+

Array Administrator’s Guide for more information.

The default for the SCSI “vendor ID field” is

Sun

. Display or change this value with

the

port

command.

The default Sun StorEdge T3 and T3+ array volume configuration as shipped from
the factory is 9 drive RAID 5 with no standby disk.

The volume is configured as follows:

■

vol add v0 data u1d1-9 RAID 5

■

vol init v0 sysarea

■

vol init v0 data rate 16

recon_rate

medium

[high, medium, low] Reconstruction rate.

memsize

Set by controller, read-only. In MBytes

cache memsize

256

Set by controller, read-only. In MBytes

TABLE B-3

Volume Defaults

Parameter

Default

Variables

init [rate

]

[1-16] 1 is lowest, 16 is highest...

verify [rate

]

[1-8] Rate parameter refers to host interleave factor
(contention with host IOs). Default is 1. There is currently
no feature that spawns a

vol verify

process.

TABLE B-2

System Default Settings

Sys Parameter

Default

Variables

Summary of Contents for StorEdge T3+

















































































































































































































































Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands

Sun Microsystems StorEdge T3+, Service Manual

Search results

Summary of Contents for StorEdge T3+

Reviews:

Related manuals for StorEdge T3+

Brands by name

Popular brands