Sirona XIOS XG Select Operating Instructions And Installation Download Page 60

Page: 60 / 120

4 Installation

Sirona Dental Systems GmbH

Gebrauchsanweisung und Installation

64 08 137 D3610

D3610.201.02.09.02 11.2017

Click the "Browse" button in the "Sensor" group and open the ".hex"
file. It is provided on a CD or via an Internet download.

Click the "Submit" button (only once).

Follow the progress indicator at the lower edge of the "Web
Server and Upgrade Utility" page.

The WiFi interface automatically reboots once the Firmware
upgrade has been fully completed. After the reboot wait approx. 10
seconds until the LED starts to flash.

10. Click the "Back" button in the Internet browser when the upgrade

successful message appears.

11. Update your Internet browser window by pressing F5 on the

keyboard and check the updated Firmware version. It is "2.4" in this
example.

12. Return to "WiFi Interface Management" window. Ensure that the

updated WiFi interface is still on the list of units detected.

13. Pair the updated WiFi interface with the PC to check its function.

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands